PsRNA:A Computing Engine for the Comparative Identification of Putative Small RNA Locations within I

来源 :基因组蛋白质组与生物信息学报(英文版) | 被引量 : 0次 | 上传用户:yueyegg
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Small RNAs (sRNAs) are non-coding transcripts exerting their functions in the cells directly.Identification of sRNAs is a difficult task due to the lack of clear sequence and structural biases.Most sRNAs are identified within genus specific intergenic regions in related genomes.However,several of these regions remain un-annotated due to lack of sequence homology and/or potent statistical identification tools.A computational engine has been built to search within the intergenic regions to identify and roughly annotate new putative sRNA regions in Enterobacteriaceae genomes.It utilizes experimentally known sRNA data and their flanking genes/KEGG Orthology (KO) numbers as templates to identify similar sRNA regions in related query genomes.The search engine not only has the capability to locate putative intergenic regions for specific sRNAs,but also has the potency to locate conserved,shuffled or deleted gene clusters in query genomes.Because it uses the KO terms for locating functionally important regions such as sRNAs,any further KO number assignment to additional genes will increase the sensitivity.The PsRNA server is used for the identification of putative sRNA regions through the information retrieved from the sRNA of interest.The computing engine is available online at http://boioserver1.physics.iisc.ernet.in/psrna/and http://bicmku.in:8081/psrna/.
其他文献
综合采用理论分析和数值计算方法,提出了双巷掘进区段煤柱合理宽度确定原则和方法。首先结合改进的Mark-Bieniawski煤柱强度计算式,求得区段煤柱强度分布规律。然后采用FLAC3
以察哈素煤矿首采工作面为工程背景,通过对工作面支架工作阻力监测以及推进数据的收集、整理和分析,对大采高综采超长工作面推进速度与周期来压步距间的关系进行了深入细致的
以南屯矿33上15工作面为背景,采用理论分析、现场实践,对厚煤层边角煤开采过程中矿压演化规律进行研究.研究结果表明:厚煤层边角煤开采时,煤壁片帮、端面冒项和支架承载较常
通过对矩形巷道围岩受力及“四区”的分析,确定了卸压槽围岩的破碎区与塑性区宽度公式.经分析可知,卸压槽破碎区与塑性区宽度随着应力集中系数增大而以非线性方式增加,并在卸
文家坡矿1~#辅运石门是煤矿的重要运输通道,现场监测表明巷道顶板与两帮围岩变形小,两帮锚杆受力较小,巷道局部有轻微底鼓,巷道处于“强顶-强帮-弱底”状态。通过现场监测、
通过ANSYS软件对万丈山隧道开挖过程中拱顶及周边的受力、变形进行了研究,并对比指导施工。结果表明:隧道开挖面实际应力与初支混凝土有效强度的最不利比值出现在第9 d,施工
分析软岩支护的机理,对当前软岩支护存在的设计、施工等方面的问题进行探讨,并阐述软岩支护应该注意的关键问题。将软岩支护技术应用于实际煤矿支护之中,比较不同支护形式的
首先应用比值判别法和“三带”判别法确定煤层群采用下行开采,然后通过理论分析得出回采巷道应采用外错式布置并计算出相应外错距,借助数值模拟软件模拟了该种情况下巷道围岩
针对平朔井工三矿井39107综放工作面过风氧化带时极易出现煤壁片帮,造成断面冒顶、易发生顶板事故的现象,采用层次分析法(AHP)对支架工作状态、回采工艺过程、地质力学等众多影
根据巷道断面尺寸、支护方式及材料等参数,以Auto CAD12.0为软件平台,利用其内嵌的Auto LISP语言进行二次开发编写绘图程序,同时使用DCL语言编制人机交流的对话框,从而完成了